Power Attenuator Calculator

Power Attenuator Calculator
The calculator enables you to design your own 50 ohm "power attenuator" built with good available resistors from the E12-series. The Calculator will calculate the resistors effortlessly and with a very good accuracy.
The calculator computes the number of resistors and the values of the resistors, which are based on the E12-series values. Due to the good availability and your own choice of the maximum power of the resistors (e.g. 1/2, 1 or 2 watts), you can get exactly what you want. 

Power Attenuator
A power attenuator is an attenuator, which is suitable for a much higher input power than is usual for an simple Pi-type attenuator. The three compound resistors that form a 
n accurate, Pi-type power attenuator, are each composed of a number of resistors in parallel. The power is distributed across the resistors. The higher the power, the more resistors are required.

Decimal Comma or Decimal Point
The use of a comma or  a point in a spread sheet adapts it self to the setting of the Langauge of the spread sheet. First consider whether your Excel spread sheet or Open Office spread sheet uses a decimal comma or a decimal point. 
                    English:  Decimal Point
     Other Langauge:  Decimal Comma 

For a NON English langauge setting use a Decimal Comma  
Click below to Download   -  For a NON English langauge

For an English langauge setting use a Decimal point
Click below to Download   -  For English langauge
Download the PA1B Power Attenuator Calculator - English
Use of the Calculator
Please familiarize yourself with the calculator and type in the data for a 
Power Attenuator of 10 dB for an input power of 1.6 W and resistors of 1/4 W.
Type in: 1,6 and 0,25 for 1/4 watt  OR  1.6 and 0.25 for 1/4 watt 
Type the data in a white input fields.  Give [Enter] or [TAB] to enter the value.
Tip: Use [TAB] to move between the 3 white input fields.

Results
The calculator will calculate the number of resistors and their values.
  
Schematic  

Since the compound resistor R1 has to dissipate 0.83 W, and each resistor can dissipate 1/4 W, at least 0.83/0.25= 3 resistors in parallel are needed. 
The compound resistor R1 is formed by 3  resistors of 330 ohm and one resistor of 820 ohms, all in parallel. 
Most of the power is dissipated in the 3 resistors of 330 ohm. The resistor of 820 ohm is added to arrive accurately on the wanted value of 96.25 ohms for R1.
The 2 resistor of 150 ohms dissipate most of the power in R2. The resistor of 1500 ohms is added to arrive accurately on the wanted value of 71.15 ohms for R2
R3 has the same value as R1, but dissipates far less power. R3 is formed by 100 ohms and 2700 ohms in parallel.

Design values
This schematic shows the values of a 10 dB power attenuator for an input power of 1.6 W

For an attenuator of the resistors R1 and R3 both have an ohmic value of 96.25 ohms. 
R2 is 71.15 ohms.

R1, R2 and R3 dissipate 52%, 33% and 5% of the input power. 



No limitations
The Calculator has no limitations on the input power nor the maximum power of the resistors.
* The Calculator will even work with an input power of more than 5 watts or with resistors of 0.25W or 0.1W.

Play with the values, see what happens, with each new choice.
Just try for fun: PIN =  100 watts to find out that it takes 103 resistors of 1 watt to make an attenuator of 10 dB for an input power of 100 watts. hi
* Don't care about the number of resistors needed. 5 Resistors of 1/2 W will take about the same space as 3 resistors of 1 W. With three or more resistors in parallel, just twist the leads of the resistors together.


Finally you can get less power then 5 watts from your 5 watts QRP set. 
With the Power Attenuator Calculator, you can design an attenuator for any input power.

Read more about attenuators on the attenuator Page.

Or go to my web site: Home - PA1B QRPp page 

4 opmerkingen:

  1. The attenuation calculator is not downloadable

    BeantwoordenVerwijderen
    Reacties
    1. Hello Menashe, thank you for informing me about the broken link. The link is corrected. Thanks, 73, Bert

      Verwijderen
  2. Thank you very interesting information

    BeantwoordenVerwijderen
    Reacties
    1. Hello Vladimir, It's my pleasure. Thank you for your reaction. 73, Bert

      Verwijderen